
Maintenance and cleaning of aluminium and steel slat fences
Slat fences are low-maintenance, not no-maintenance. A simple routine keeps the finish looking right and catches small problems before they become expensive.
Why does a slat fence need cleaning at all?
In short: because salt, dust and organic dirt sit on the coating and, over time, attack the finish and the fixings.
Powder-coated aluminium and coated steel are durable, but the coating is what protects them and keeps the colour. On the Costa del Sol, three things settle on a fence: salt carried by sea air, fine dust (including the reddish dust that arrives with a calima), and organic dirt from trees, irrigation and birds.
On their own, none of these destroys a fence quickly. But salt that stays wet in grooves, or dirt that holds moisture against a scratched area, is where corrosion begins. Regular cleaning is the cheapest way to keep any aluminium slat fence looking as it did on handover day.
What is a sensible cleaning routine?
In short: rinse with fresh water, wash gently with a mild detergent when needed, rinse again, and do it more often close to the sea.
A practical routine:
- Rinse the fence with fresh water from a garden hose, top to bottom, both sides where you can reach.
- Wash with a soft sponge, cloth or soft brush and water with a little mild, neutral detergent when the surface looks dull or dirty.
- Rinse again thoroughly so no detergent dries on the surface.
- Dry spots can be wiped with a soft cloth if you want to avoid marks on dark colours.
How often depends on where you are. Plots right by the sea, and fences that the sprinklers do not wash, benefit from more frequent rinsing than an inland garden. The manufacturer of your slat system may give specific recommendations; follow them where they exist.
What should you never use on a coated fence?
In short: abrasive pads, wire brushes, strong solvents, acidic or alkaline cleaners, and a pressure washer held close to the surface.
Most damage to fence finishes comes from cleaning, not from the weather. Avoid:
- scouring pads, steel wool and wire brushes;
- solvents, thinners and strong degreasers;
- acidic or strongly alkaline products, including some patio and limescale cleaners;
- pressure washers used close up or at a sharp angle, which can lift coatings at edges.
If you are cleaning paving next to the fence, protect the fence from splashes of paving cleaner. And if a gardener is responsible for the outside areas, tell them which products are safe for the fence.
What should you do about scratches and chips?
In short: on aluminium, clean and touch up with a compatible product; on steel, act quickly before rust spreads; replace badly damaged slats.
Scratches happen – ladders, garden tools, balls, a car door. The response depends on the material:
- Aluminium does not rust like steel, but a scratch through the coating exposes bare metal that can oxidise and look untidy. Clean the area and use a touch-up product compatible with the coating.
- Steel slats and profiled sheet need faster attention. Any chip down to bare steel can start rusting, especially near the sea; treat it promptly.
- Wood-effect finishes are hard to touch up invisibly. Replacing the damaged slat is often the cleaner solution, which is why we suggest keeping a few spare slats.
For colour matching and finish types, see colours and finishes.
What should you check once a year?
In short: fixings, post bases, caps, the bottom of the fence and the wall underneath.
Once a year, walk the whole line and look at:
- Screws and fixings – tighten anything loose and look for rust stains around screw heads.
- Post bases – check that base plates are firm and that water does not stand around them.
- Caps and end profiles – replace missing caps, which keep water and debris out of the posts.
- The bottom of the fence – keep soil, mulch and plants off the lowest slat.
- The wall – if your fence stands on a murete, look for cracks around the post fixings.
If you live abroad, ask whoever looks after the house to send photos of these points. If something looks wrong, send them to us and we will tell you whether it needs attention. Our wind and slatted fences guide explains why fixings matter on exposed plots.
How do plants and irrigation affect the fence?
In short: constant watering and plants in contact with the slats keep the surface wet and dirty; adjust sprinklers and leave a gap.
Hedges and climbing plants soften a slat fence, but they also hold moisture against it. Sprinklers that hit the fence every evening leave mineral deposits on dark colours and keep the bottom of the fence permanently damp.
Simple fixes: angle sprinklers away from the fence, leave a small gap between hedges and slats, and avoid letting climbers grow into the slat channels. On a fence on a wall, the murete and its coping keep most garden water away from the slats.
Articles and guides

Aluminium slat fence: privacy for Costa del Sol villas
A clean, low-upkeep screen made of aluminium profiles between posts – one of the most requested fences for modern villas, and one that is only as good as the structure underneath it.
View details →
Steel slat and profiled sheet fence: a solid, practical screen
When the priority is a tall, fully closed screen along a longer boundary, steel slats or profiled sheet are often the practical answer – as long as the coating, the fixings and the posts suit the site.
View details →
Aluminium fences near the sea: what salt air really does
Most of our clients live within reach of the sea breeze. That is a good reason to choose aluminium – and a reason to pay attention to coatings, fixings and details.
View details →
Colours and finishes for aluminium and steel slat fences
Colour is the decision owners spend longest on, and the one most often limited by community rules. A few principles make it much easier.
View details →Frequently asked questions
How often should I clean an aluminium fence?
It depends on location. Near the sea, more frequent rinsing helps; inland, an occasional wash is usually enough.
Can I use a pressure washer?
Only with care, on a low setting and at a distance. Close-up pressure washing can damage coatings, especially at edges.
What detergent is safe?
A mild, neutral detergent diluted in water is usually safe. Avoid acidic, strongly alkaline and solvent-based products.
How do I remove calima dust?
Rinse first to remove loose dust, then wash gently. Rubbing dry dust into the surface can scratch it.
Do I need to wax or polish the fence?
Not normally. Follow the slat manufacturer's advice if they recommend a specific product.
What causes white marks on dark slats?
Often mineral deposits from irrigation water or detergent left to dry. Rinsing thoroughly and adjusting sprinklers helps.
Can I paint over my aluminium fence?
It is possible with the right preparation and products, but rarely needed. A repaint is a specialist job.
What if the fence starts to lean?
Do not wait. Send us photos; leaning usually points to a footing, fixing or wall problem.
How do I clean louvred panels?
Rinse from both sides and use a soft brush between the blades, where dust and salt collect.
Is maintenance different for steel slats?
The routine is the same, but scratches need faster treatment because exposed steel can rust.
Planning a slat fence for your villa?
Send photos of the boundary and the approximate length. We reply with a first assessment and, after a visit, an itemised quote with no commitment.